Sewn up a 4 mag 995 Redball leg rig for customer

Sewn up a black 500D Cordura leg rig, for 4x 20rd Redball 995 magazines, no MOLLE; adjustable leg straps, and adjustable height.

It is meant for a left thigh; in which a righthanded shooter can use his/her weak arm

to draw the magazines.

Retention is by velcro.

 

DSCF1499

View of loaded rig

DSCF1500

Close up of the magazine pockets.

DSCF1501

 

leg adjusting straps detail; I used 1.5″ ITW-Nexus loops for the free end straps so that they do not flop around, this is to make it look cleaner in execution.

DSCF1502

View of the belt loop and adjusting strap on the upper buckles. The loops are sized to fit 2.25″ USGI Pistol Belts at the widest; so they should be compatible with pretty much any standard belt; other than MOLLE patrol belts.

DSCF1503

Velcro retention straps and pull tabs.

DSCF1504

Close up of the bottom of the rig; showing the pleated layout. This ensured a clean looking pocket with the magazines inserted.

 

 

 

 

Advertisements

OD lumbar pack for MOLLE I waistbelt and V strap adapters

Built a large lumbar pack for the 1st generation MOLLE (MOLLE I) ruck waistbelt; as the belt is quite sturdy and has attachments which allows the user to attach an ALICE buttpack to it. Materials; 1000D Cordura Nylon in Tactical Tailor Olive Green; 1″ Nylon webbing in OD #7, ITW-Nexus hardware. Approximately 740 cubic inches, a little over 12 liters.

DSCF1436

The large MOLLE Lumbar pack on the 1st gen MOLLE belt

DSCF1438

Side view

DSCF1437

Upper view

DSCF1449

Shown with 1980s ALICE OD butt pack, and 1990s-2000s ALICE/MOLLE butt pack (really is ALICE but were issued with the 1st gen MOLLE items)

DSCF1443

Close up of the top 1.5″ triglide mounts to stabilize the lumbar pack to the 1.5″ webbing

I also made a set of V strap adapters to interface with Tactical Tailor’s padded MAV harness; and to enable users to attach to the 1st gen MOLLE waist belts, of both types

DSCF1439

Shown attached to the MOLLE I Ruck waist belt; You can see how the waist belt has the hardware for the ALICE butt pack, with metal loops for the woodland butt pack’s lashing straps.

DSCF1448

On a standard 3 piece MOLLE I utility belt; they are commonly found either missing the 1.5″ vertical webbing, or with a different belt attached (either SPEAR ELCS or MOLLE II). The outboard sleeves are nearly identical to the SPEAR ELCS H harness pieces, only they have 3 metal rectangle loops to connect the 1st generation vest panels.

DSCF1440

Close up of the adapter. I used ITW-Nexus’ Strap dividers for 1.5″ webbing, 1.5″ webbing tapered to points, and sewn to 1″ webbing.

DSCF1441

Close up of the lower ends of the V straps, using 1″ Tri-glides and utilizing 3 of the waist belt’s metal loops (There are a total of 12; 6 per side, for adjusting where the vest panels go)

DSCF1444

Pouch/pack attached, 2x Combat Medic Vest system triple ammo pouches, 2x canteen covers, 2x Tactical Tailor Large utility pouches, 1x Tactical Tailor Zippered medic pouch, and the lumbar pack.

DSCF1445

Showing the gap between the pouches for the 1″ webbing to go through.

DSCF1446

Upper view with belt standing up

DSCF1447

On Utility belt; with all 3 sections adjusted smallest possible; from outboard to center; 2x Grenade pouches, 2x CMVS triple ammo pouches, 2x Canteen pouches, 1x SAW 100rd pouch with old  ALCIE?M1967 Jungle First Aid Kit’s plastic box insert.  This set up is very similar to the ELCS H Harness, or Eagle DFLCS H harness, or any of the older PLCE/H-Harness rigs offered by Eagle, London Bridge Trading Company, Blackhawk! Industries, and British Tactical.