1700 cubic inch low profile ALICE pack

Made this in Coyote Brown 500D Flame Retardant Cordura.

Approximately 22 inches by 13 inches by 6 inches.

Minimal MOLLE on it

Drawcord top closure

Simple slick top flap

Fits 4 different frames; can be used frameless.

Don’t quite know the weight of the packbag itself.

Frameless, with ALICE straps

Shown on the ALICE frame

Medium MOLLE/DEI 1609 frame with attachment details

On FILBE/DEI 1606 MC frame with FILBE Suspension

Shown on 26″ish Outdoors Products Ram-Flex/Small Coleman Peak 1 frame

With 2x Tactical Tailor Large Utility Pouches and 1x Woodland Sustainment Pouch, and expedient rigged horizontal lash strap to retain side pockets

A-Tacs FG pyramid tarp tent

Sewed up this pyramid shelter out of 5 yards of  Polyurethane/silicon coated waterproof 1.9oz Ripstop Nylon in A-Tacs FG camouflage colors. Final measurements are 7 ft 10 inches long, 4 ft, 7 inches wide, height at peak, 50 inches. I will have to redo the door closure system to get the overlap needed for further weatherproofing.

There are a total of 11 tie out loops, I may add a few more if it would enable one to do more variety in setups like a blind or an observation post, or something similar to that.

Right now the support it uses are 2 standard aluminum adjustable tarp/awning poles lashed together… it will be changed out for something more low visibility later on.

On to the photos!

 

DSCF1957

Progress photo; door triangles cut and laid next to edge of front of main body, it is folded here, it should show how it looks when laid flat and folded in half.

DSCF1962

front view of the shelter; You can see how the doors have no overlap, and a serious gap that would allow weather to go in….so it is being redone right now.

DSCF1963

Side view, please pardon the USGI poncho peeking out, the poncho is  quite a bit wider than the shelter; The slight inclination of the door panels is evident here. One could add a rectangular tarp or poncho awning here for more space and for cooking/dining/general activities.

DSCF1964

The back view of the shelter, You can see the additional tie outs in the center of each of the 3 edges, and the center of the primary seam line on the back panel. The roof tie out is in case the user wants to have additional space inside the shelter, and the other tie outs are for more secure staking of the shelter in high wind areas, or for alternate shelter layouts to make up for space restrictions.

DSCF1966

Inside shot of the shelter with the doors folded back. The extra length is apparent here compared to the USGI poncho, and the relative narrowness is also evident here. I chose this width and length for a single person with room enough for gear/equipment/furred partner (dogs!), although two persons can snuggle up in there if needed.

DSCF1965

Close up of the door closure system, 1st try. It is simply 6 US Army BDU buttons, and elastic loops that fits on them. The loops will be replaced by something else that would provide me with the overlap needed to keep weather out. This is one of the lightest, most silent methods of closures that I can think of for the purposes of this shelter.

DSCF1967

Shown rolled and wrapped with the single peak line. The Coyote Brown  roll is the Bushcraft USA 10×10 Coyote tarp made of the same type of fabric (1.9oz PU coated Ripstop nylon). The pyramid shelter rolls into a smaller package, and is a bit lighter, even with the door closures being included.

MYOG MOLLE Yucca Pack!

Made a MOLLE version of the Boy Scouts Yucca/ Green Bar Bill Pack; using 1000D DCU Cordura scraps….. Since I wanted a day pack that was in between the size of a Recon Buttpack and the size of a normal Schoolbag or the Medium Ruck sack…plus the ability to add or subtract pouches to it….I looked into my sewing fabrics drawer and out came the DCU Cordura material…I did not have enough width to make the pack the way  I make my pouches, but I had enough material to make a pack a little differently; with two side panels sewn to the main panel.

DSCN2170

Bare pack; with straps undone..yes the flap is ridiculously long, but its for a reason

DSCN2176

Flap opened up to show full height of the panel; 6 rows and 6 slots of MOLLE

DSCN2171

Side of pack; with 6 rows and 3 slots of MOLLE; for attachment of whatever you could want. Could thread cord through some slots and use that to compress the sides if needed?

DSCN2172Bottom of pack with 3 rows and 4 slots of MOLLE, for attachment of either MOLLE Waistpack or lashing straps for gear

DSCN2173

Back of pack without shoulder straps attached. The D-rings are for shoulder straps obviously, but they could also be used to strap to a frame or a larger ruck sack if one wanted to.

DSCN2175

Top of pack, showing the “ear flaps” to keep most weather out. I might add snaps to the edges to seal better…

DSCN2174Its like a cave of T-shirts! there’s enough space for up to 3 or 4 days of clothing in there….provided you put the rest of your camp gear outside it…as these next two pics will show!

DSCN2178

All packed up for a summertime/warm weather camp trip! Green sack has my modified Kelty topquilt, and then there’s the freebie Coleman inflatable pad on the bottom…the two squarish pouches holds food, first aid kit, and small batwing tarp. The long horizontal pouch holds tarp stakes, guylines, compass, misc gear.

I have two canteen pouches on this as well;

DSCN2177

The back showing the canteen pouches in use with canteens and cup and canteen stove; and their small pockets hold my Swiss Army Knife, and fire kit. You can see that I am using USGI LC-2 straps for backpacking duty, I could clip the pack to the black webbing harness I have which have two hooks for small packs such as this.

Hope you enjoyed this post!

 

UPDATE on this post! I have more pictures and detail shots of the pack!

DSCN2179

With pad and stuff sack removed, and black shotgun pouch added and small knife attached to MOLLE KA-BAR adapter. It is shown next to the small Recon Buttpack

DSCN2180

Better shot of the side and showing how much the three coyote pockets add to the depth of the pack

DSCN2181

detail shot of attachment of shotgun ammo belt pouch via ALICE to MOLLE adapter

DSCN2182

With green stuff sack up top

DSCN2183

Comparo shot of complete overnight-3 day pack next to large MYOG hiking backpack