Wall Tent Mod to USGI Pup Tent!

Made a wall tent mod to the USGI Shelter Half pup tent similar to what is described in this article from the Boy Scouts magazine;

http://books.google.com/books?id=4gGnPTm6dicC&pg=PA16&lpg=PA16&dq=Boy%27s+Life+The+Pup+Grows+Up&source=bl&ots=K1JoUu71hr&sig=VT_92khq36DyE38kqHy8Gwt1SmA&hl=en&sa=X&ei=ecFuVNWJDMLkiQLphoHwDg&ved=0CCcQ6AEwAA#v=onepage&q=Boy%27s%20Life%20The%20Pup%20Grows%20Up&f=false

instead of following the cut instructions in the magazine article, I decided to cut the 6 wall panels from two scrap shelter halves rectangle panels, thus making it simpler and easier to attach to the shelter halves for this mod.

DSCN2164

The layout for cutting; bottom piece is full length of rectangle, and 15″ tall while the two corner walls are 16″ tall and 48″ long, the extra width is for making a rolled hem on the bottom of each shorter rectangles.

DSCN2165

Set up using tree straps and cargo straps attached to two trees; this is the lightest set up possible (NO POLES!)

DSCN2166View into the unbuttoned end, showing the V line from single stake to the corner loops.

DSCN2167Side view, you can see the W shaped lines from the loops to the two stakes on each side; plus the V lines from the single stake to the corner loops.

DSCN2168

Closed up end, with single stake. I realize I could have positioned the tree straps higher so that the 14″ walls are at full height, but this is OK.

DSCN2169End opened up (5 stakes now) showing the Intex Full Size airbed, it is a little over 54″ wide, and approx 10″ tall, and 75″ long, and in this “mini wall tent”; there is plenty of space on the sides and back of the bed, with the corners only just touching the back walls, and still covered completely with the end opened up. THis is also a good set up for being in front of a fire or a small tent heater or tent stove for cold nights. The tent is also pretty heavy, so it is again, NOT a backpacking tent, but it is great for cold weather camping!

Hope you enjoyed this post! πŸ™‚

 

6-man USGI shelter half set up

I’ve been quite busy this holiday season…though… I picked up two complete USGI Pup Tents, and have made this 6-man shelter out of 6 shelter halves, 12x pole sections, and four 9ft poles assembled from the Greatland Cabin tent… the external A-frame set up was a pain in the butt to do, but this was all by myself, not with another person which might’ve made it easier to set up…

using this page as a guide;

http://www.hardscrabblefarm.com/vn/tent-pitching.html

 

I followed most of the directions and made the shelter; it is around 12 feet by 12 feet octagon, with roughly 5 feet wide long edges and 4 feet corner edges, and around 8 feet tall, this shelter gives a group of people a lot of space, and depending on what they bring, has room enough for a heater or a wood stove if the pipe can go out somewhere…

DSCN2163

corner shot, the triangle opening is the entry opening, one could do without a 4th wall in the base and use an open face set up next to a fire with the top triangle end folded back

DSCN2162

sideways angle view, you see the Inverted V rope, that is part of a W shaped guy line because I did not check to make sure the top halves have snap buttons on the bottom edges..whoops

DSCN2161

closed up corner view. On building the base, I found I do not need to have a 4th wall to keep the other 3 suspended, so that provides another way to have entrance or one could combine multiple pieces to make for a huge communal shelter.

The whole shelter is very heavy, and would NOT be good for backpacking at all, unless spread out by people. It might be possible to carry all of it on a gear sled in winter, or a wheeled cart in spring and fall…

Well Tomorrow or so I will do other set ups and take pics!

 

 

Redone Whelen shelter set up!

I decided to try for an overnight trip out to Cascadia area in the Willamette National Forest….using my Modified Whelen setup using USGI Shelter Half parts….well. Weather took a turn for the cold and I was unable to maintain core temperatures so I had to give up the overnight part…Oh well! This set up uses 3 whole halves and two cut triangle ends from a fourth half..USGI poles and two steel poles, and 10 stakes. Took a long time to get the fire going…and I used two wool-blend blankets plus a 3/8 inch CCF foam pad underneath my modified USGI Intermediate Cold weather mummy bag….wearing wool socks, wool sweater, nylon pants and a cotton undershirt…as well as the USGI ECW parka inside the sleeping bag, I was still unable to stop the coldness from the ground.

The shelter has one half as a floor on top of an USGI poncho, while two halves are used on the top parts plus the triangle parts as panels in between the two halves.

Here are the photos of the camp set up!

DSCN2154Whelen style/Baker style set up. At first I thought I set it up way too close to the fire, but later in the evening it proved to not be the case.

DSCN2155

Another view of shelter set up

DSCN2156

Sleep area, showing the poles and the floor cloth used, along with the bags for storage of everything. I used my MYOG backpack to carry the complete shelter, and the black MSS bag to carry the wool blankets and the sleeping bag. The blue CCF pad went under the top flap.

DSCN2157Later, due to the smoke coming into the shelter, I took the awning off.

DSCN2158

Another view of the set up without awning

DSCN2159By this time, it was getting REAL cold, and I wasn’t sure if there was going to be some rain or snow, so I set up the awning again, but this time folded the ends over so that the wind will keep blowing the smoke out of the shelter, wind direction was mostly parallel to the shelter face.

For the next cold weather camp trip, I am going to attempt to make either an Ammo Can stove or a Popcorn Tin stove, and order polypropylene long johns for a base layer.

 

MYOG hiking backpack

Unable to afford or justify spending a lot of money on a backpack that has all the features I wanted; I decided to make my own pack bag to use with both my ALICE frame and Civilian Hiking frame; andΒ  presumably is also compatible with MOLLE frames of both types; the MOLLE DEI 1603 (Standard MOLLE large frame) and MOLLE DEI 1609AC (MOLLE Medium frame now issued in USMC)… so I bought 2 yards of fabric, measured and cut patterns, and spent several hours sewing it all together… In hindsight, if I were to order a pack with these features, it would be over a 100 dollars… Oh well! the pack is a little over 55 Liters, and is pretty light…not as heavy as the ALICE pack, but not as light as the hiking backpack, mainly due to the webbing and plastic Fastex buckles..the Side Pouches are sewn like the ALICE pack pockets, basically tunneled so that I can slip long items in between the pouch and pack body. Features are;

Made of 430 Denier Nylon,

Overall size; 20″Wx22″Hx9″L

Main upper compartment 12″x9″x13″

Main lower compartment 12″x9″x9″

Upper side Pouch 9″x11″x4″

Lower side Pouch 5″x5″x3″

Attachment system; Ladder locks and 1″ webbing straps

Webbing for canteens (after finding out not enough room to sew water bottle pockets..whoops)

10 Fastex buckles, 8 frame attachment points

DSCN2131

Pack next to Coleman PEAK 1

DSCN2132

Quarter view of pack showing side pockets

DSCN2133

Webbing for LC canteen covers, can use for other LC pouches

DSCN2134Upper frame attachments

DSCN2135Bottom of pack

DSCN2136Drawstring panel on bottom of pack, I might make an U shaped panel with elastic on bottom to cover the drawstring panel and flap; not sure yet.

DSCN2137

Upper side pouch, it’s based on the MOLLE Sustainment pouch size, and uses two buckles instead of one for better securing; I do not use webbing keepers, since the straps can be used to compress pouches and hold things like folded up sweaters or tarps or poncho

DSCN2143

On the ALICE LC frame

DSCN2142Back view with LC frame, showing attachments

DSCN2139Bottom attachments on LC frame

DSCN2140Lower corner attachment on LC frame; it uses the round hole to attach, just like the standard ALICE pack

DSCN2141Top corner attachment to LC frame

In theory it probably would be more comfortable using either a Canadian pattern 82 suspension or MOLLE Hellcat suspension system…

 

Vintage pack suspension system update, and picked up a good tarp!

Decided I wanted to add a centering strap to my Academy Broadway’s modded suspension system so that it stays in one place instead of being quite floppy….its simply a 1.5″ wide nylon belt threaded through the center piece and attached to the two bars where the straps are attached to…wearing it, I do not notice it at all! With a 22 pound base load without water, it feels very comfortable…DSCN2105 Showing the centering strap

DSCN2101 How the pack sits on me, and how the straps goes down following my back to the mounting points on the lower bar, it also shows the load lifter as it should be used;

DSCN2104

Another view of the set up, but from the side. I realize the load lifters aren’t at the “magic 45 degree” angle, but it is comfortable and I do not feel overburdened.

I also picked up a 9×7 rubberized nylon tarp….it only has 8 grommets, and is thinner than my USGI poncho, but heavier than the silnylon tarp I have….it is in a shade very close to that of Coyote Tan, though according to an older backpacker, it was available at REI and other outfitters in the 80s as a lightweight alternative to the poly plastic tarps and canvas tarps at that time.

20140915_133756

Laid out flat

20140915_133806Showing the material on both top and bottom side

20140915_132316Set up over the 2-man bug tent and hiking poles (improvised from ski poles)

20140915_132306View from the front, the fabric sags pretty heavily in this set up…

20140915_132332From the side, it covers all of the bug screening, and there is plenty of room in between the front/back and the tarp, one could move it back a little and have a porch/awning to store gear under.

20140915_133410I think this is the better set up, no spots for water to pool under…I might modify the bug tent to have only two side pull outs instead of four…so that I can use the same stakes on the sides as the diamond with door pitch uses….

20140915_133420

Side view of the diamond with door pitch;

20140915_132407Center seam on the ridge; I think this is likely the reason for the sagging..not sure myself…

20140915_132414Hiking/Ski poles used to support the tarp. it is the perfect size to hold up through the grommets…I will be getting rubber feet or tip protectors for them so as not to scratch rocks when hiking/backpacking…

And here are the two packs packed up for 3-4 days with the significant other…… minus water.

 

DSCN2106

I am carrying a Full size air mattress plus wool blanket and canteens in the top, clothes in middle, sleeping bag in bottom, food in front large pocket, extra rope in one pocket, fire starting kit in small pocket, first aid kit in other pocket, with the last large pocket being available for miscellaneous things, while her red pack carries her sleeping bag, the bug tent and the tan tarp with stakes, food in side pockets with room for miscellaneous items, canteens in the main compartment with her clothes underneath the sleeping bag…weights are as follows, my big green one is 22 pounds without water, her red bag is 17 pounds without water…a difference of 5 pounds which could be attributed to the wool blanket and heavier clothes, since she is basically half my size.

Whelen style tent from USGI shelter halves

In memorial of the people whose lives were extinguished in NYC at World Trade Center..

After watching this video; I was inspired by the set up shown near the end of a lean to that is based on the Whelen Tent lean to, but using USGI Shelter Halves… so from this video;

[url]https://www.youtube.com/watch?feature=player_embedded&v=2AnsFLEHMZ4[/url]

I modified one of my shelter halves, and because I loathe unfinished edges, I hemmed the cut edges on the end triangles, the rectangle awning is already hemmed, so I don’t need to worry about that. The twist from the video set up, is that I don’t have the USGI pole sections, but I have a bunch of metal tent poles from other shelters, and with the correct bottom pole sections, I was able to get the same lengths as the tent’s panels, so I am able to use 4 poles in A-frame format and not worry about knocking poles out from centers…The awning poles are hollow and went right on top of the stakes holding down the triangles, so they aren’t moving anywhere..for actual set ups, I will add the webbing pole pockets from my hammock spreader bar project, and tie them to the corner loops on the shelter halves so that the poles will stay put.

20140910_154758View of the set up;

20140910_154809Quarter view of the tent; showing the unobstructed space between the poles and the main living section. It is wide enough for a full size air mattress should one wish to put in there…it is excellent for setting up right next to a camp fire, as it is canvas and was treated with fire resisting materials, which is probably worn off…

20140910_154827The back view of the tent; it looks like a standard army tent, with an awning added to it.

20140910_154841Interior shot, showing the poles’ layout and the holes in the awning from wear and tear…I will probably patch them up.

Looking at the set up, I think I could get a complete tent system, and put an unmodified half where the awning is, and have the end triangles hang down vertically to where the poles meet at the bottom, and put the other unmodified half on the floor, and use the rectangle awning section as a door, to make for as complete a shelter as possible for two people.

 

 

 

Two Shelter set ups!

Acquired a pair of USGI Shelter Halves, no poles nor stakes, but that was OK with me, as I have poles and stakes to spare…..decided to set up the USGI shelter halves in a format similar to the Whelen Lean-To shelters, and decided to set up the 9×12 poly tarp in a pyramid format with two long poles….DSCN2090

the USGI Whelen lean to set up. If I acquire another shelter half fabric piece, I could cut the triangles off and use those to fill in the gaps on the above set up…and have the rectangle become a small floor piece..

DSCN2091

Another view of the shelter, from the side. it uses 10 stakes and 6 guy lines…a lot of lines indeed.

DSCN2092

Back view of shelter. it is room enough for two to lay in, so it would be a good campfire shelter..might be covered more with the addition of the two triangles if I find a 3rd shelter half.

And here is the 9×12 pyramid shelter set up; it is very spacious inside, and can comfortably sleep 3 persons…or two people and a weeks worth of gear.

DSCN2088Two long poles in a bipod/scissors form, 4 stakes total and entrance could be covered by an USGI poncho tied to the two stakes and the peak. The format is simply that it is suspended at the center of the 12 ft side, so there is 6 feet between the center and the door corner stakes, and it is a little less than 9 feet from door stake to the corner stakes…as that is the 9 ft side..with that much space, one could put two cots, or an air mattress.. and still have plenty of room.

DSCN2089

view from the side, one could in theory put a tie out using a pebble in the middle of the long triangle panel, and pull it out to provide more room if needed.

 

 

 

External Frame packs and Vintage ALICE Goodness!

Decided to do redo my hiking backpacks and return the Improved Hellcat pack frame to stock format of Coleman PEAK-1 bag, original straps and all; and packed it with stuff for the Significant Other except her clothes….What is surprising is that the removal of the military equipment cut out around 5 pounds of unnecessary weight; though at the loss of modularity….right now with stuff except clothes and water, it weights 16 pounds overall. The big green Academy Broadway Jasper pack is full of stuff except water, and carries extra items for two people, weights in at 22 pounds, but empty, the pack weights around 5.5 pounds, still a significant weight loss compared to the MOLLE equipped Coleman pack frame before. I also decided to return one of my old ALICE bags to a like-new ALICE frame and stock straps/belt (all 1978-1979 vintage and NO SCRATCHES OR DAMAGE!) that was given to me by the S.O.’s mother, turns out empty, it weights 9 pounds….only 2 pounds less than the MOLLE version, and still almost double the empty weight of the Jasper pack and the Coleman PEAK 1 pack.Β  Also did the Bobcat Mod on a camo ALICE bag with camo LC-2 straps, its not bad but not good for heavy loads.

DSCN2080

The three external frame bags;

DSCN2081View of their suspension components;

 

DSCN2082

Bobcat modded Medium ALICE

DSCN2083View of Bobcat modded ALICE straps;

DSCN2076

Loaded up before I transferred all the crap in there to the Jasper pack; here, it weighted 32 pounds O.O (with a full 1 gallon of water and too much food, enough for like 5-6 days hahaha)

DSCN2075

showing the Bobcat mod, which consists of a 11″ long steel tube in the frame pocket and the straps attached around it to the metal rings of the pack. It works OK, but is best for lighter loads than whats shown here.

OK, people are probably wondering HOW is it I have so much stuff in those bags…..for the purposes of pictures, the ALICEs are loaded with extra items I have.

Academy Broadway Jasper pack list;

-blue CCF pad

-12×9 poly tarp

-10 stakes

-bug tent in lower compartment

-first aid kit in side pouch

-granola bars and chocolate packets in side pouch

-fire kit in small side pouch

-2 pairs of pants

-2 shirts

-2 pairs of underwear

-3 pairs of socks

-fleece pull over

-2 2qt canteens (empty right now)

-Kelty top quilt

-Food for 3 days

-canteen cup

-weight currently at 22 pounds without water.

Coleman Peak 1 pack

 

-Down 20 degrees mummy bag (too small for me, but perfect for S.O.)

-2 1qt canteens (also empty)

-canteen cup

-kitchen items; forks, spoons, skewers and pot holder

-2-3 days of food

-granola bars

-weight 16 pounds, no water or clothes

Green Medium ALICE pack

-empty weight; 9 pounds (EEK)

-twin air mattress

-one old sleeping bag

-two empty canteens

Camo Medium ALICE pack; Bobcat mod

-MOLLE straps inside

-MOLLE belt inside

-2x MOLLE sustainment pouches and MOLLE panels

-2x USGI 3 day training packs

-Hex tarp

-Bat-wing tarp

-extra stakes

-hammer

-total weight; 18 pounds

 

Out of all the packs, the Jasper’s modified waist belt fits the best, 2nd only to the MOLLE hip belt, and the Coleman Peak 1 straps are the most comfortable, 2nd only to the MOLLE shoulder straps… the belt it has is too small for me; so its ok for the S.O. for now. The worst straps is a tie between the Jasper straps and the ALICE LC-2 OD straps on the stock ALICE pack. The Jasper straps’ metal buckles are right in front of my armpits, where they should NOT be…..however, the upper mounts is at the perfect 45% angle, so I think I only need to modify the straps by extending the upper mount somehow. Not sure how to best proceed….There is the option of making complete new straps with a set of cannibalized LC-2 long straps similar to the woodland ones in OD, with which I would mount the bottom of the backs to the lower cross bar between the top and the bottom, and have load lifters to the original strap cross bars, this would give me 6 points of adjustment. Ideally if there was another bar below the cross bar, that would be the perfect place for new straps…I am not sure what model Kelty is closest to this frame… Or Jansports for that matter.

As for the Hellcat mods; I think I want to do it again with a DEI 1606AC frame, and probably with new, lighter materials similar to the set up on the Coleman Peak 1 pack, but in Olive or Camo…

For actual bug out bags, it is hard to beat the practically indestructible ALICE packs, especially with the Hellcat mods…..When one considers the need for the fabric to actually stand up to abuses such as dragging in the mud, tossing in the truck, or whatever vehicles have you, and so on….the ALICE and the MOLLE equipment are pretty good for that… BUT….unfortunately, it can also make you a target, hence my decision to pack these two civilian hiking backpacks, which are pretty tough, and also pretty much common everywhere (the Kelty/Jansport style one, not sure of the Coleman but…)…and so will aid greatly in the “gray man” thinking. Out here in the PNW, people do not give second thoughts or focus on the bearded guy wearing surplus winter jackets and a civilian hiking pack; nor do they focus on the obviously large hunting camo wearing guy with the old army backpack and old hunting rifles….In some areas, people are more attracted to the guy who wears 5.11 everything and has a black or coyote backpack with miles of MOLLE; but they do not really notice the guy with woodland/desert MOLLE; nor do they notice the guy with the 30+ year old framed hiking backpack.

Tarp shelters for bug tent!

Did 3 different set ups of tarp protection for the bug tent; here is one using the Bat Wing tarp; rotated 90 degrees from the usual, giving it a sort of cartwheeling star shape……

20140831_135302

it provides more protection on the sides than the previous set up; but not by much; as seen below…

20140831_135320

if I attached “beaks” of some sort from where the pole stakes are to where the side stakes are; then possibly one would have more coverage there…but then again, it might be better without the bug tent itself…

20140831_135700

One or two people could lay at a diagonal in this shelter without the bug netting; and that would be more effective.

20140831_135651

Without the bug tent underneath, there is quite a lot of room underneath for two people laying side by side or slightly diagonally.

SO I decided to do a set up with the 9×12 poly tarp;

DSCN2068

It gives the bug tent so much more room; and is very breezy..

DSCN2069

completely covered; and with space enough to hang items off a ridge line above the tent such as a lamp or boots or clothes; however it is heavy due to being poly plastic.

DSCN2071

view from the back; I didn’t line up the bug tent perfectly but oh well. Note that the bug tent’s side pull outs aren’t utilized here, its more to do with time…

DSCN2070

another view looking into the door; the door panels are tied to the tarp grommets so that its easy to let air in, and easy to find in the dark.

And here is the final set up, one I probably would use more often…I just need to get the thing waterproofed; my DIY asymmetric Hex tarp;

DSCN2078

It looks like the corners of the bug tent are exposed, but that is a trick of the eye, looking directly above, the bug tent is completely covered.

DSCN2077

view from the front with doors closed; there is not much of a gap between the bug netting and the tarp; this is due to the tarp being an odd shape and due to my not so perfect seam sewing on the center seam of the tarp. The pull outs are utilized here, with cord running to the tarp’s stakes, so that I do not need to pack 4 more stakes. 10 stakes overall for each of the three set ups.

DSCN2079

View from the back; there is ample room on each side for gear and various items, and the poles are around 48 inches tall I think, so a couple trekking poles at that length would do very well to reduce weight of set up, OR two trees conveniently located in a straight line with a flat surface in between (ha ha ha ha not likely) OR one tree and a car with a roof rack (more likely); Although it would be nice to have a pick up truck or a flatbed truck on which I can simply tie down the bug tent and suspend a tarp over it; that is not going to happen any time soon.

I believe this hex tarp, while normally for the two hammocks, would do great as a ground shelter for this bug tent πŸ™‚

Β 

Tested modified bug tent, and made hammock bug net!

Modified an old Stansports A-frame “Scout backpacking” tent that was not waterproof into a bug tent to be more airy…it is 54″ wide by 78″ long, and 36″ tall…. Unlike the original tent design, I added two more tie-outs on the sides, so that I could expand the feel of the tent and make it more spacious compared to original design. I was able to test it with the girlfriend on an overnighter in the Willamette National Forest. It is comfortable and very airy..perfect for the summertime! We put a Twin size air mattress in the tent, there’s still enough room for small gear on the sides, though ideally a Full size air mattress at 54″ wide would be preferable for two people so as not to risk rolling off the air mattress and landing on the ground. With the relative lack of privacy in the bug tent, we set up another small tent, a dome tent for use as changing room, and as back up tent should we need it.

Also made a bug net for my hammock, these pics are of it before I added another section of bug netting to extend it….and the stuff sack holds everything for hammock except tarp and tarp lines/stakes.

DSCN2054

Campsite on NFS 4695 past Humbug Campground; yes that is an army cot in the foreground, I forgot to bring proper chairs so we used that by the fire πŸ™‚

DSCN2055

Another view of campsite, the tarp BARELY covers the tent, for rain, I would probably use a larger tarp.

DSCN2056

The bug tent under the bat wing tarp, the girl is in the tent testing it. I utilized a couple long poles for the support of the tent and tarp, if needed, one could dispense with them and use trekking poles or pitch from trees. The bug netting is 59×84 panel of polyester sheer curtain material from Kmart; I decided one panel is all it needed to make the tent a bug tent.

DSCN2022

Hammock bug net made of two panels of the same polyester sheer curtain material; shown with the under pad and the hammock; not shown is the new extension panel I added to it due to it being too small for the hammock really….. (accidentally ripped one side’s hole a bit bigger…)

DSCN2023

Hammock stuff stuffed into MSS bag; yes that is how bulky it is when not compressed; open cell underpad, top quilt, hammock, bug net, suspension straps are all in there. only the tarp stuff is separate.

DSCN2024

Nice thing about the MSS bag; the 9 strap compression system helps compress the stuff into this basketball sized unit…though on my pack, I don;t compress it as far, since I need it to be slimmer so that my MOLLE pouches and straps will fit.

DSCN2058

A view of the creek next to the campsite πŸ™‚ This creek, I’m not sure which one it is, but it feeds Brietenbush River which feeds into Detroit Lake from the mountain springs.

DSCN2063Another view of the creek, water is ice cold….brrr.

DSCN2064Different section of the creek.

DSCN2065Started a twig fire underneath a rotten log end that someone left behind.

DSCN2067

The stump getting on fire….it lasted for about 10-12 hours…..we had hot dogs for dinner that night πŸ˜€