Bushcraft USA 10×10 tarp set ups and one tree hammock hanging system!

Recently acquired a Bushcraft Outfitters, USA (BCUSA) 10 ft by 10 ft coyote tarp in a forum deal! It was damaged with a tab broken off, I got the tab repaired… anyhow… DSCN2338

Coyote Brown BCUSA tarp in brown stuff sack next to el-cheapo pencil organizer that houses my lighter smaller Long Ogee tarp.

DSCN2341

Damaged tab repaired, I used 1″ Cross- Grain ribbon as the reinforcement material and stitched lines to make sure it aint ever coming off!

DSCN2339

Initial set up, Diamond fly configuration with ski poles, 2 stakes only! a little slack in the material but that’s expected of nylon fabric..

DSCN2342

With two hammocks, more than enough space in there…. I know, I hung the hammocks too low like low hanging fruit but it’s just to give one an impression of the space available..

And with this tarp, I’ve decided I wanted to see how it would look in a vastly different configuration than most of the normal square tarp set ups…the basic layout is the same for the next 3 set ups, just the differences are all in the ridge line tie out location and the configuration of the front opening.

20150517_172644

Front view of the tarp tent set up;

20150517_172626

Back view of the set up, What I did is to stake the back wall down first, and then square up the side corners so that the tabs, which are evenly spaced at 2.5 ft between tie out tabs, are able to be staked down at the same locations, and then from that point between the center and the outermost stake, line up the front corners of the shelter to make a rectangle floor print of 5 ft wide and 7.5 feet long.

20150517_172611

Side view. After I stake the sides/corners down, I then raised the front peak up as far as I could do, and then attached the two tarp clips at the points where I wanted to raise the roof/wall points on the back, to make for a nearly vertical rear wall, and then ran the lines to the ski poles and staked them down. Finally, I run the clothesline ridge line through the ridge seam tabs on the tarp and raised the rear peak up, and tied the end of the line to an overhanging branch. This in effect gives the shelter a house like roof from which rainwater will shed very well, and with the vertical walls, gives one a feeling of increased space compared to a typical A- frame.

20150517_173318

Having seen something similar on a same size tarp, I decided to see if it would work with the ridge line peak tie out moved back 2.5 feet to the next tie out tab on the ridge seam..and bungee’d the resulting corners to bring the front down as far as I could… I disliked this set up because it robs the interior of space, and essentially makes it more a shelter you can only lay diagonally, as opposed to straight up and down.

20150517_173306

Another view of the terrible layout. It might be OK if I had done this with the back being a normal A-frame back though.

20150517_173940

So, keeping the same ridge line tab tied out, I decided to see what would happen if I pulled the corners the other way..and supported them with leaning poles and guy lines… this was the result. A much much better set up, and one that gives me the most spacious feel of the interior, PLUS the protection from almost all angles, the front opening is only 2.5 feet tall and 5 feet wide, a poncho or a small 5×7 tarp folded in half would have provided a great awning/door..One could also put a small piece of bug netting on that area and be fine for bug season…

20150517_173952

The side view of it. It is essentially now a doghouse shaped shelter, and with the amount of room up front now that the gable is pulled further out, one could have a good space for cooking/gear and still be protected from the elements inside.

20150517_174004

Rear view of the Doghouse shelter, again it is showing the rear wall layout, but also, you can see how much more open the front part looks to be compared to the first triangular opening shelter.. And the only two changes from that is the relocation of the ridge line peak tie out point and the addition of two tie out/pole points on the front sides.

With the tarp clips relocated to exactly 2.5 ft from the corners and in line with the side tabs and the ridge tab, I would say the shelter is basically a small wall tent with a front opening.
And now for something quite different! Here’s the one tree hammock stand!

One Tree Hammock stand stuff

First, these are the materials you need, from top to bottom;

a hammock obviously, with suspension.

an USGI General Purpose, Medium Tent center pole, telescoping, and it goes out to 10something feet, so if you ever need to have a visual cue on “not touching this with a 10ft pole”, this is it!

then the camo straps which are for both the hammock attachment and a ridge line in between the one tree and the pole,

then finally, a set of 4 cargo straps with 10″ nail style stakes larksheaded to their ends and tied to each other at their centers.

DSCN2361

Hook up the ridge line with the camo straps, then position army pole, only extended halfway, then run the 4 green straps down to the ground, and nail them securely at a 45 degree angle.. the pole is not vertical, because that is not what you want, you want as much of the hammock load to be on the pole, and less on the lines, so angling the pole out that its around 50-60 degrees from vertical, and then make sure its not going anywhere.. then stake the lines as far as possible.. this in effect gives you a tension based system..

finally, hook up the hammock to the pole and tree strap.

DSCN2360

Another view of the system, with my massive lumbar pack hanging off a steel hook I mounted on the tree strap. Sharp eyed readers will note that I have a whoopie sling in between the two straps on the ridge line, this is to make it easy to maintain tension…

DSCN2359

With the 10×10 tarp set up in an almost ordinary set up… first I put the side up with the poles, then I staked the center of the other side to make a half-diamond shape..then I staked out the “door” sides on the covered side. This gives me a good balance of wind proofing from one side, and yet a nice porch mode on the other side… with the amount of space in there, I can have a 2nd hammock underneath if I dare do so, or an army cot, or a camp chair or two..

DSCN2358

Side view of the set up. I did not stake the lefthand door as close to the ground as the other side is, but it still works here. With the short hammock ridge line, the 10 ft tarp covers me very well…only problem is the gear hanging out in the rain, but a poncho over it will give it the protection it needs.

Hope you enjoyed this post!

Advertisements

Tarp Shelter layouts and set ups!

Decided to go and do several different tarp shelter designs and layouts with the 5×7 tarp, Bat wing tarp, 9×7 tarp, and the latest 10×14 tarp I recently got!

DSCN2205

Flying Diamond pitch, Harbor Freight 5×7 tarp;

DSCN2206

Windward side view, first, tie upper corner to tree or post, then stake diagonal opposing corner down, then stake remaining two corners to make a wind break

DSCN2207

Another view of the Flying Diamond pitch with the 5×7 tarp, it does not provide much protection from rain, but is good for sun shade and possibly as a fire reflector using a pole to support the high corner.

DSCN2201

Batwing tarp in a symmetric diamond pitch with doors staked out on one side.

DSCN2202

Quarter view on windward side, the doors on the ground corner have been folded under, thus turning this tarp into a rhombus of 9 ft ridge line and 7 ft width.

DSCN2203

Head on windward view, the rhombus shape is all too readily apparent here, I think this is a good one man shelter, maybe two if the two people like cuddling together.

DSCN2204

Detail of doors on the pole side. Since the doors are not exactly vertical from the peak, they will go out past the pole or tree, and I might add tarp tie outs on the junction between the doors and the sides, so as to provide a place to stake out further, or suspend between two poles or trees.

DSCN2208

Another 5×7 tarp set up, Low Tetra pyramid…or “Dead Man’s bivy bag” set up due to its tiny size.

DSCN2209

The height of this is around 30 inches, while the width is 60 inches at the far end, and a floor length of 7 feet. This is NOT an ideal shelter for tall people, but for the average user or shorter, it would be a survivable shelter with protection from most elements.

DSCN2210

Windward view, one could make it feel bigger by adding a tie out/panel pull out where the sticker is on this tarp.

DSCN2215

Half-Pyramid open faced shelter utilizing the tan 9×7 tarp and suspended from a Douglas Fir branch.

DSCN2216

Windward view of the tarp shelter

DSCN2217

Tree side view, that is a 5×7 tarp as the ground cover, and there is plenty of room in there for up to 3 people. Best with two and gear, and with a metal pole or similar, one could have a fire in front of the pyramid shelter and be comfortable.

DSCN2218

Interior view with ground cloth and my MOLLE pack in there.

DSCN2224

10×14 tarp set up in a 6×8 narrow pyramid with approx 7 ft height.

DSCN2225

View of door side with door flaps closed up.

DSCN2226

Interior view showing the basic fold of corners and the space given.

Basically one puts tarp clips 3 feet from the corner of the door flaps, for the front, and then put tarp clips an approximate distance (in this case, 4 feet) from the corners on the back to make a 6 ft width between the back two clips, and thus providing just around 8 ft of length between the front and the back after squaring up the stake points.

DSCN2227

With 9×12 tarp erected using 5 more pole sections as an awning.

DSCN2228

Not quite lined up I know, but this gives good space under which to dine or cook or hang around in weather.

DSCN2229

A different pyramid set up, this oddly enough gives me a bigger floor space than the narrow one above, the doors are now 4 feet wide, and the back edge is now 8 feet wide..there is a 6×8 tarp in there, and according to my calculations and confirmed with this set up, I have a floor of 8 ft wide and 6 feet 6 inches length, thus providing me with more useful room in the shelter. Same 7 ft approximate height.

DSCN2230

Closed up, basically weather proof. I could cut a hole in there for a stovepipe but I do not have a stove with pipe yet.

DSCN2231

Side view of Leaning/half Pyramid set up.

DSCN2232

Windward-quarter view, showing the better pyramid shaping compared to the narrow one.

DSCN2233

All packed up save for the pole. I might splurge for a backpacking tarp pole if it means a smaller package than that shown above. Both the 10×14 tarp and the 6×8 ground tarp are rolled up in the bag, along with the stakes and the single long line.

Hope you enjoyed this post!